How to Choose the Right Belt Size for Men
Most men buy a belt in the same size as their trousers, and that's usually one size too small. A belt goes around the outside of your trousers, so it needs a little extra length. Get it wrong and you end up on the last hole, or with a long tail flapping past the first loop. Here's how to choose the right leather belt size the first time.

The quick rule: trouser size plus 2 inches
For office trousers and chinos: belt size = trouser waist + 2 inches. A 32-inch waist takes a 34-inch belt.
For jeans: belt size = jeans waist + 4 inches. Jeans sit lower on the hips and the denim is thicker, so you need more length.
Trouser sizes also vary a lot between brands, and many are cut slightly bigger than the label says. If you want to be sure, measure yourself using the steps below.
Men's belt size chart
| Trouser waist | Belt size (trousers) | Belt size (jeans) |
|---|---|---|
| 28" | 30" | 32" |
| 30" | 32" | 34" |
| 32" | 34" | 36" |
| 34" | 36" | 38" |
| 36" | 38" | 40" |
| 38" | 40" | 42" |
| 40" | 42" | 44" |
| 42" | 44" | 46" |
| 44" | 46" | 48" |
Need a bigger size? Our XXXL belts fit waists up to 66 inches. For all Oxhide sizes in one place, see our size guide.
How to measure your belt size in 3 steps
1. Wear the trousers you'll use with the belt. Pull them up to where you normally wear them.
2. Run a soft measuring tape through the belt loops, the same way a belt would go.

3. Pull it snug and read the number to the nearest inch. That number is your belt size.
Don't have a tape? Lay a belt that fits you well flat on a table and measure from the end of the buckle to the hole you use most. That's your size too.
How a belt should fit
A well-sized belt fastens on the middle hole, usually the third of five. That leaves room to loosen after a big meal or tighten if you lose a little weight. The end of the strap should reach just past the first belt loop, not stop before it or wrap around to your side.
Ratchet belts work differently
A ratchet belt has no holes. You trim the strap to fit and it clicks into place in small steps of about 5 mm, so the exact size matters less. If you're deciding between the two, read our guide: Ratchet Belt vs Normal Belt.
Which belt width should you choose?
Length is only half of a good fit. The width decides whether the belt suits your outfit and slides easily through your trouser loops.
- 30mm – slim and neat, best for suits and dress trousers with narrow loops. See our formal belts.
- 35mm – the everyday width for office wear and smart casual outfits.
- 38mm – wider and sturdier, made for jeans and chinos. See our casual belts.
If you only own one belt, 35mm is the safest choice.
Three sizing mistakes to avoid
Ordering your trouser size. A 32-inch belt on 32-inch trousers usually ends up on the last hole, or doesn't close at all.
Measuring to the wrong hole. When you measure an old belt, look closely: the hole you really use is slightly stretched or darker than the others. Measure to that one.
Measuring over a T-shirt. Thick fabric like denim adds length. Always measure through the belt loops of the trousers you'll actually wear.
Frequently asked questions
Is belt size the same as pant size?
No. A belt sits on top of your trousers, so it needs to be longer. Go one size up from your trouser waist, which is about 2 inches, or two sizes up for jeans.
What if I'm between two sizes?
Choose the larger size. A slightly long belt can be fixed with an extra hole, but a short one can't be made longer.
My belt is too big. What can I do?
Bring it to any Oxhide store and we'll punch an extra hole for you on the spot, free of charge.
Do you have belts for larger waists?
Yes. Our XXXL belts fit waists up to 66 inches.
Found your size?
Full-grain leather, made to last. Shop online or visit us at NEX, Waterway Point and Jurong Point.
Shop leather belts Shop ratchet beltsORDER NOW and we ship your order NEXT DAY !
- ✔ In stock – Shipping HK$40 Only
- ✔ Return withing 30 days – No Questions Asked !